当前位置： 首页 > news >正文

南通网站开发工作纪律和生活纪律研讨发言材料

news 2025/9/17 6:53:57
南通网站开发,工作纪律和生活纪律研讨发言材料,工作室怎么网站备案,渠道游戏官网Android Wifi连接和断链分析思路。 1.密码错误导致的连接失败 2.关联被拒绝 3.热点未回复AUTH_RSP或者STA未收到 AUTH_RSP 4.热点未回复ASSOC_RSP或者STA未收到ASSOC_RSP 5.DHCP FAILURE 6.发生roaming 7.AP发送了DEAUTH帧导致断开连接 8.被AP踢出，这个原因…

Android Wifi连接和断链分析思路。

1.密码错误导致的连接失败

2.关联被拒绝

3.热点未回复AUTH_RSP或者STA未收到 AUTH_RSP

4.热点未回复ASSOC_RSP或者STA未收到ASSOC_RSP

5.DHCP FAILURE

6.发生roaming

7.AP发送了DEAUTH帧导致断开连接

8.被AP踢出，这个原因需要sniffer log分析

下面详细介绍。

1.密码错误导致的连接失败

1.1

其实有时候并不是用户真的输入了错误密码，有可能WIFI底层驱动存在异常。

可以查一下WIFI配置文件中保存的AP密码是否与期望值一致。

wpa_supplicant: wlan0: WPA: 4-Way Handshake failed - pre-shared key may be incorrect
wpa_supplicant: wlan0: CTRL-EVENT-SSID-TEMP-DISABLED id=0 ssid="inhub" aut

1.2 在4WAY_HANDSHAKE阶段由于密码错误、丢帧或者弱信号丢包导致WRONG_KEY：

密码错误在4WAY_HANDSHAKE阶段中的2/4次握手会显示wrong key。如果已经连接过则显示

I/wpa_supplicant(19043): wlan0: CTRL-EVENT-SSID-TEMP-DISABLED id=1 ssid="inhub" auth_failures=1 duration=5 reason=WRONG_KEY。

丢帧导致连接断开：

wlan: [24597:E :PE ] limHandleMissedBeaconInd: 2121: Sending EXIT_BMPS_IND to SME due to Missed beacon from FW

信号弱导致断开：

I/wpa_supplicant(31023): wlan0: CTRL-EVENT-DISCONNECTED bssid=c8:3a:35:2b:71:30 reason=0
E/WifiStateMachine( 821): NETWORK_DISCONNECTION_EVENT in connected state BSSID=c8:3a:35:2b:71:30 RSSI=-89 freq=2437 was debouncing=false reason=0 ajst=0

reason=0表示因为信号弱而断开。

2.关联被拒绝

2.1

wpa_supplicant: wlan0: CTRL-EVENT-ASSOC-REJECT status_code=1
wpa_supplicant: wlan0: Request to deauthenticate - bssid=00:00:00:00:00:00 pending_bssid=00:00:00:00:00:00 reason=3 state=ASSOCIATING
wpa_supplicant: wpa_driver_nl80211_disconnect(reason_code=3)

2.2 在ASSOCIATING阶段由于丢包导致ASSOC REJECT

Line 15551: 03-10 15:42:04.953 884 884 I wpa_supplicant: wlan0: CTRL-EVENT-DISCONNECTED bssid=f4:2a:7d:7c:65:df reason=3 locally_generated=1
Line 15552: 03-10 15:42:04.959 884 884 W wpa_supplicant: nl80211: Was expecting local disconnect but got another disconnect event first
Line 18957: 03-10 15:42:07.363 884 884 I wpa_supplicant: wlan0: Trying to associate with f4:2a:7d:7c:65:df (SSID='inhub' freq=2412 MHz)
Line 18965: 03-10 15:42:08.372 884 884 I wpa_supplicant: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=f4:2a:7d:7c:65:df status_code=1
Line 18991: 03-10 15:42:08.693 884 884 I wpa_supplicant: wlan0: Trying to associate with f4:2a:7d:7c:65:df (SSID='inhub' freq=2412 MHz)

上面日志分析

CTRL-EVENT-DISCONNECTED bssid=f4:2a:7d:7c:65:df reason=3 ==>这是系统下断线的
重连后有看到CTRL-EVENT-ASSOC-REJECT==>有可能跟网络有关,

若是当前环境下WiFi 比较多(2.4G环境比较糟,干扰较大，有可能某一方收发不好导致),

若是一直都出现CTRL-EVENT-ASSOC-REJECT导致连线不上，最好找WiFi 方案商帮忙协助确认一下是否是WiFi端的问题？

3.热点未回复AUTH_RSP或者STA未收到 AUTH_RSP

正常情况下，STA发送AUTH request后，会收到一个AUTH_RSP，即正确情况下，内核LOG中会有如下两行打印，异常情况下，仅有第一行。

这种情况下，可以用其他设备接入AP，看是否存在同样的问题，则基本判断出是否为热点问题。

4,20619,2759068545,-;AUTH - Send AUTH request seq#1 (Alg=0)...
4,20620,2759170874,-;AUTH - Receive AUTH_RSP seq#2 to me (Alg=0, Status=0)

4.热点未回复ASSOC_RSP或者STA未收到ASSOC_RSP

异常情况下，STA端不会有下面的第二行日志打印。

[ 2854.218696] ASSOC - Send ASSOC request...
[ 2854.238083] PeerAssocRspAction():ASSOC - receive ASSOC_RSP to me (status=0)

5.DHCP FAILURE

四次握手成功但是获取IP地址失败：

WifiConfigStore:  message=DHCP FAILURE

正常情况下的流程如下：

DhcpClient: Broadcasting DHCPDISCOVER
DhcpClient: Received packet: 10:c7:53:71:ae:7c OFFER, ip /192.168.236.146, mask /255.255.255.0, DNS servers: /192.168.236.1 , gateways [/192.168.236.1] lease time 86400, domain null
DhcpClient: Got pending lease: IP address 192.168.236.146/24 Gateway 192.168.236.1  DNS servers: [ 192.168.236.1 ] Domains  DHCP server /192.168.236.1 Vendor info null lease 86400seconds
DhcpClient: Broadcasting DHCPREQUEST ciaddr=0.0.0.0 request=192.168.236.146 serverid=192.168.236.1
DhcpClient: Received packet: 10:c7:53:71:ae:7c ACK: your new IP /192.168.236.146, netmask /255.255.255.0, gateways [/192.168.236.1] DNS servers: /192.168.236.1 , lease time 86400
DhcpClient: Confirmed lease: IP address 192.168.236.146/24 Gateway 192.168.236.1  DNS servers: [ 192.168.236.1 ] Domains  DHCP server /192.168.236.1 Vendor info null lease 86400 seconds

6.发生roaming

当前连接AP1信号太弱，此时又扫描到了已连接过的AP2，AP2的信号强度更好，则会断开AP1，连接AP2，这一系列动作就叫roaming。 

如下列中，断开了与10:0e:0e:20:66:15热点的连接，连接到了10:0e:0e:20:5e:6d热点。

wpa_supplicant: nl80211: Associated on 2422 MHz
wpa_supplicant: nl80211: Associated with 10:0e:0e:20:66:15
wpa_supplicant: nl80211: Drv Event 47 (NL80211_CMD_ROAM) received for wlan0
wpa_supplicant: nl80211: Roam event
wpa_supplicant: nl80211: Associated on 2472 MHz
wpa_supplicant: nl80211: Associated with 10:0e:0e:20:5e:6d

日志2

I/WifiHAL (28360): event received NL80211_CMD_ROAM, vendor_id = 0x0
I/wpa_supplicant(28064): wlan0: CTRL-EVENT-CONNECTED - Connection to c4:14:3c:29:47:25 completed [id=0 id_str=]
I/WifiHAL (28360): event received NL80211_CMD_ROAM, vendor_id = 0x0
I/wpa_supplicant(28064): wlan0: CTRL-EVENT-CONNECTED - Connection to c4:14:3c:29:47:05 completed [id=0 id_str=]
I/WifiHAL (28360): event received NL80211_CMD_ROAM, vendor_id = 0x0
I/wpa_supplicant(28064): wlan0: CTRL-EVENT-CONNECTED - Connection to 1c:1d:86:e9:e2:85 completed [id=0 id_str=]

7.AP发送了DEAUTH帧导致断开连接

此时可以连接其他AP测试一下，进而判断是否是刚才这个AP的问题

[ 1555.321037] (1)[3319:tx_thread][wlan] Rx Deauth frame from BSSID=[aa:63:df:4c:db:c2]
[ 1555.321093] (1)[3319:tx_thread][wlan] Reason code = 7

8.被AP踢出，这个原因需要sniffer log分析

reason=2，reason=7，reason=15代表被AP踢出，在kernel log中可以找到对应的deauth信息。

I/wpa_supplicant(28064): wlan0: CTRL-EVENT-DISCONNECTED bssid=c4:14:3c:29:47:05 reason=7
wlan: [28055:E :PE ] limProcessDeauthFrame: 144: Received Deauth frame for Addr: 44:a4:2d:52:bc:a5 (mlm state = eLIM_MLM_LINK_ESTABLISHED_STATE, sme state = 12 systemrole = 3) with reason code 7 from c4:14:3c:29:47:05
I/wpa_supplicant(28064): wlan0: CTRL-EVENT-DISCONNECTED bssid=1c:1d:86:e9:e2:85 reason=15
wlan: [28055:E :PE ] limProcessDeauthFrame: 144: Received Deauth frame for Addr: 44:a4:2d:52:bc:a5 (mlm state = eLIM_MLM_LINK_ESTABLISHED_STATE, sme state = 12 systemrole = 3) with reason code 15 from 1c:1d:86:e9:e2:85
I/wpa_supplicant(28064): wlan0: CTRL-EVENT-DISCONNECTED bssid=c4:14:3c:29:47:25 reason=2
wlan: [28055:E :PE ] limProcessDeauthFrame: 144: Received Deauth frame for Addr: 44:a4:2d:52:bc:a5 (mlm state = eLIM_MLM_LINK_ESTABLISHED_STATE, sme state = 12 systemrole = 3) with reason code 2 from c4:14:3c:29:47:25

其他情况后续补充。

附录：

802.11 Association Status, 802.11 Deauth Reason codes

802.11 Association Status, 802.11 Deauth Reason codes - Cisco Community

802.11 Association Status Codes

Code

802.11 definition

Explanation

0

Successful

1

Unspecified failure

For example : when there is no ssid specified in an association request

10

Cannot support all requested capabilities in the Capability Information field

Example Test: Reject when privacy bit is set for WLAN not requiring security

11

Reassociation denied due to inability to confirm that association exists

NOT SUPPORTED

12

Association denied due to reason outside the scope of this standard

Example : When controller receives assoc from an unknown or disabled SSID

13

Responding station does not support the specified authentication algorithm

For example, MFP is disabled but was requested by the client.

14

Received an Authentication frame with authentication transaction sequence number
out of expected sequence

If the authentication sequence number is not correct.

15

Authentication rejected because of challenge failure

16

Authentication rejected due to timeout waiting for next frame in sequence

17

Association denied because AP is unable to handle additional associated stations

Will happen if you run out of AIDs on the AP; so try associating a large number of stations.

18

Association denied due to requesting station not supporting all of the data rates in the
BSSBasicRateSet parameter

Will happen if the rates in the assoc request are not in the BasicRateSet in the beacon.

19

Association denied due to requesting station not supporting the short preamble
option

NOT SUPPORTED

20

Association denied due to requesting station not supporting the PBCC modulation
option

NOT SUPPORTED

21

Association denied due to requesting station not supporting the Channel Agility
option

NOT SUPPORTED

22

Association request rejected because Spectrum Management capability is required

NOT SUPPORTED

23

Association request rejected because the information in the Power Capability
element is unacceptable

NOT SUPPORTED

24

Association request rejected because the information in the Supported Channels
element is unacceptable

NOT SUPPORTED

25

Association denied due to requesting station not supporting the Short Slot Time
option

NOT SUPPORTED

26

Association denied due to requesting station not supporting the DSSS-OFDM option

NOT SUPPORTED

27-31

Reserved

NOT SUPPORTED

32

Unspecified, QoS-related failure

NOT SUPPORTED

33

Association denied because QAP has insufficient bandwidth to handle another
QSTA

NOT SUPPORTED

34

Association denied due to excessive frame loss rates and/or poor conditions on current
operating channel

NOT SUPPORTED

35

Association (with QBSS) denied because the requesting STA does not support the
QoS facility

If the WMM is required by the WLAN and the client is not capable of it, the association will get rejected.

36

Reserved in 802.11

This is used in our code ! There is no blackbox test for this status code.

37

The request has been declined

This is not used in assoc response; ignore

38

The request has not been successful as one or more parameters have invalid values

NOT SUPPORTED

39

The TS has not been created because the request cannot be honored; however, a suggested
TSPEC is provided so that the initiating QSTA may attempt to set another TS
with the suggested changes to the TSPEC

NOT SUPPORTED

40

Invalid information element, i.e., an information element defined in this standard for
which the content does not meet the specifications in Clause 7

Sent when Aironet IE is not present for a CKIP WLAN

41

Invalid group cipher

Used when received unsupported Multicast 802.11i OUI Code

42

Invalid pairwise cipher

43

Invalid AKMP

44

Unsupported RSN information element version

If you put anything but version value of 1, you will see this code.

45

Invalid RSN information element capabilities

If WPA/RSN IE is malformed, such as incorrect length etc, you will see this code.

46

Cipher suite rejected because of security policy

NOT SUPPORTED

47

The TS has not been created; however, the HC may be capable of creating a TS, in
response to a request, after the time indicated in the TS Delay element

NOT SUPPORTED

48

Direct link is not allowed in the BSS by policy

NOT SUPPORTED

49

Destination STA is not present within this QBSS

NOT SUPPORTED

50

The Destination STA is not a QSTA

NOT SUPPORTED

51

Association denied because the ListenInterval is too large

NOT SUPPORTED

200
(0xC8)

Unspecified, QoS-related failure.
Not defined in IEEE, defined in CCXv4

Unspecified QoS Failure. This will happen if the Assoc request contains more than one TSPEC for the same AC.

201
(0xC9)

TSPEC request refused due to AP’s policy configuration (e.g., AP is configured to deny all TSPEC requests on this SSID). A TSPEC will not be suggested by the AP for this reason code.
Not defined in IEEE, defined in CCXv4

This will happen if a TSPEC comes to a WLAN which has lower priority than the WLAN priority settings. For example a Voice TSPEC coming to a Silver WLAN. Only applies to CCXv4 clients.

202
(0xCA)

Association Denied due to AP having insufficient bandwidth to handle a new TS. This cause code will be useful while roaming only.
Not defined in IEEE, defined in CCXv4

203
(0xCB)

Invalid Parameters. The request has not been successful as one or more TSPEC parameters in the request have invalid values. A TSPEC SHALL be present in the response as a suggestion.

Not defined in IEEE, defined in CCXv4

This happens in cases such as PHY rate mismatch. If the TSRS IE contains a phy rate not supported by the controller, for example. Other examples include sending a TSPEC with bad parameters, such as sending a date rate of 85K for a narrowband TSPEC.

802.11 Deauth Reason Codes

Code802.11 definitionExplanation
0ReservedNOT SUPPORTED
1Unspecified reasonTBD
2Previous authentication no longer validNOT SUPPORTED
3station is leaving (or has left) IBSS or ESSNOT SUPPORTED
4Disassociated due to inactivityDo not send any data after association;
5Disassociated because AP is unable to handle all currently associated stationsTBD
6Class 2 frame received from nonauthenticated station

NOT SUPPORTED
7Class 3 frame received from nonassociated stationNOT SUPPORTED
8Disassociated because sending station is leaving (or has left) BSSTBD
9Station requesting (re)association is not authenticated with responding stationNOT SUPPORTED
10Disassociated because the information in the Power Capability element is unacceptableNOT SUPPORTED
11Disassociated because the information in the Supported Channels element is unacceptableNOT SUPPORTED
12ReservedNOT SUPPORTED
13Invalid information element, i.e., an information element defined in this standard for
which the content does not meet the specifications in Clause 7		NOT SUPPORTED
14Message integrity code (MIC) failureNOT SUPPORTED
154-Way Handshake timeoutNOT SUPPORTED
16Group Key Handshake timeoutNOT SUPPORTED
17Information element in 4-Way Handshake different from (Re)Association Request/Probe
Response/Beacon frame		NOT SUPPORTED
18Invalid group cipherNOT SUPPORTED
19Invalid pairwise cipherNOT SUPPORTED
20Invalid AKMPNOT SUPPORTED
21Unsupported RSN information element versionNOT SUPPORTED
22Invalid RSN information element capabilitiesNOT SUPPORTED
23IEEE 802.1X authentication failedNOT SUPPORTED
24Cipher suite rejected because of the security policyNOT SUPPORTED
25-31ReservedNOT SUPPORTED
32Disassociated for unspecified, QoS-related reasonNOT SUPPORTED
33Disassociated because QAP lacks sufficient bandwidth for this QSTANOT SUPPORTED
34Disassociated because excessive number of frames need to be acknowledged, but are not
acknowledged due to AP transmissions and/or poor channel conditions		NOT SUPPORTED
35Disassociated because QSTA is transmitting outside the limits of its TXOPsNOT SUPPORTED
36Requested from peer QSTA as the QSTA is leaving the QBSS (or resetting)NOT SUPPORTED
37Requested from peer QSTA as it does not want to use the mechanismNOT SUPPORTED
38Requested from peer QSTA as the QSTA received frames using the mechanism for which
a setup is required		NOT SUPPORTED
39Requested from peer QSTA due to timeoutNOT SUPPORTED
40Peer QSTA does not support the requested cipher suiteNOT SUPPORTED
46-6553546--65 535 ReservedNOT SUPPORTED
98Cisco definedTBD
99Cisco defined
Used when the reason code sent in a deassoc req or deauth by the client is invalid – invalid length, invalid value etc		Example: Send a Deauth to the AP with the reason code to be invalid, say zero
http://www.yayakq.cn/news/128873/

相关文章：

  • 做swf网站营销软文范例大全
  • 网站后台 请示天津市建设工程交易信息网
  • 企业策划营销中心网站网页优化
  • 百度推广还要求做网站企业文化墙设计网站推荐
  • 东台市住房和城乡建设局闷网站海东营销网站建设服务
  • 新都网站开发wordpress的插件
  • 游戏门户网站有哪些做纯静态网站怎么样
  • 建设网站的总结搜索引擎优化seo的策略主要有
  • 做本机网站青岛网站建设q479185700棒
  • 仿站教程深圳网站关键词优化公司
  • 做数据表格的网站网站开发制作入什么科目
  • 如何做自己的播报网站做网站十大公司哪家好
  • 如何用word做简单的网站58同城网网站建设
  • 公司企业网站制作wordpress数据库损坏网站
  • 长沙建设公司网站网站 提交入口
  • 如何利用模板建站WordPress连接微博
  • 网站建站服务公司农业信息门户网站建设方案
  • 网站开发按前端后端分解中小学网站建设排行2017
  • 旅游网站排名前十新沂建设网站
  • 企业网站源码哪个最好网站后台都有哪些
  • 建网站开发费用登陆建设银行官方网站
  • 昆明做网站的公司郴州网站建设找哪家公司
  • 网站策划与建设阶段的推广互联网网站建设价格
  • 赣州网站制作培训安徽网站推广优化
  • 做网站的关键词是指开发网站价格
  • 都匀网站新加坡网站大全
  • 宁波企业建站程序wordpress 去除下划线
  • 免费网站软件下载大全2018免费的行情软件网站下载入口
  • 中国响应式网站建设保定网络公司电话
  • 网站建设的方案模板下载全案营销的案例及成功案例